Effects of Nano Precipitates in Austenite on Ferrite Transformation Start Temperature during Continuous Cooling in Nb-Ti Micro-alloyed Steels
スポンサーリンク
概要
- 論文の詳細を見る
In the present paper, transformation behavior during continuous cooling in non-deformed and hot deformed Nb–Ti micro-alloyed steels was investigated by using the thermal dilation method. Ti content in Nb–Ti bearing steels varied from 0 to 0.031 mass% with Nb content being kept to be constant. Thermal dilation curves were measured at different cooling rates, from which continuous cooling transformation (CCT) curves were built up. For non-deformed Nb–Ti steels, it was observed that ferrite transformation start temperatures (Ar3) decreased with increasing Ti content up to 0.015 mass%, leveled off in the range of 0.015 to 0.027 mass% Ti, and drastically decreased thereafter. For hot deformed Nb–Ti steels, Ar3 temperature did not exhibit significant difference with Ti addition lower than 0.027 mass%, and decreased drastically by further increasing Ti content. Austenite grain size (Dγ), Nb–Ti precipitates and residual strain were taken into account to explain the variation of Ar3 temperatures. Based on the experimental results, mathematical models for the calculation of Ar3 for non-deformed and hot deformed Nb–Ti micro-alloyed steels were developed.
- 社団法人 日本鉄鋼協会の論文
- 2007-11-15
著者
-
Yuan Xiangqian
The State Key Laboratory of Rolling and Automation, Northeastern University
-
Liu Zhenyu
The State Key Laboratory of Rolling and Automation, Northeastern University
-
Jiao Sihai
Institute of Research and Development, Baosteel Co.
-
Liu Xianghua
The State Key Laboratory of Rolling and Automation, Northeastern University
-
Wang Guodong
The State Key Laboratory of Rolling and Automation, Northeastern University
-
Liu Zhenyu
State Key Lab of Rolling Technologies and Automation, Northeastern University
-
Wang Guodong
State Key Lab of Rolling Technologies and Automation, Northeastern University
-
Wang Guodong
The State Key Lab Of Rolling & Automation Northeastern University
-
Liu Xianghua
State Key Lab Of Rolling Technologies And Automation Northeastern University
-
Liu Xianghua
The State Key Lab Of Rolling & Automation Northeastern University
-
Wang Guodong
The State Key Lab. Of Rolling And Automation Northeastern Univ.
-
Yuan Xiangqian
The State Key Laboratory Of Rolling And Automation Northeastern University
-
Liu Zhenyu
The State Key Lab. Of Rolling And Automation Northeastern Univ.
-
Jiao Sihai
Institute Of Research And Development Baosteel Co.
-
Liu Zhenyu
The State Key Lab. Of Rolling & Automation Northeastern Univ.
関連論文
- Effects of Nano Precipitates in Austenite on Ferrite Transformation Start Temperature during Continuous Cooling in Nb–Ti Micro-alloyed Steels
- Segregation in Twin Roll Strip Cast Steels and the Effect on Mechanical Properties
- Determination of Upper Limit Temperature of Strain-induced Transformation of Low Carbon Steels
- The Effect of Delay Time after Hot Rolling on the Grain Size of Ferrite
- The effect of delay time after hot rolling on the grain size of ferrite
- Segregation in Twin Roll Strip Cast Steels and the Effect on Mechanical Properties
- Texture Development and Formability of Strip Cast 17% Cr Ferritic Stainless Steel
- Effects of Nano Precipitates in Austenite on Ferrite Transformation Start Temperature during Continuous Cooling in Nb-Ti Micro-alloyed Steels
- Hydrodynamics of Large Jetting Fluidized Bed
- Effect of TMCP Parameters on the Microstructure and Properties of an Nb-Ti Microalloyed Steel
- Inversed Phosphorus Segregation in Twin Roll Cast Strips for Improvement of Mechanical Properties and Weathering Resistance
- Effect of Cooling Rates and Compressive Deformation of Austenite on Bainitic Transformation and Microstructure for Plastic Die AISI P20 Steel
- Interface Characteristic and Properties of Stainless Steel/HSLA Steel Clad Plate by Vacuum Rolling Cladding
- The Optimal Design for the Production of Hot Rolled Strip with "Tight Oxide Scale" by Using Multi-objective Optimization