Effects of Snout and Support Roll on Transport Phenomena in a Hot Dip Plating Bath
スポンサーリンク
概要
- 論文の詳細を見る
- Japan Institute of Metalsの論文
- 2003-07-01
著者
-
Iguchi Manabu
Division Of Material Science And Engineering Graduate School Of Engineering Hokkaido University
-
Kurobe Jun
Steel & Technology Development Laboratories Nisshin Steel Co. Ltd.
-
Iguchi Manabu
Division Of Maetrials Science And Engineering Graduate School Of Engineering Hokkaido University
関連論文
- Physical-modeling Study of Fluid Flow and Gas Penetration in a Side-blown AOD Converter
- Swirl Motions Caused by Horizontal Gas Injection with an L-Shaped Lance
- Rising behavior of air-water two-phase flows in vertical pipe ofpoor wettability
- Merging Distance of Two Air-Water Vertical Bubbling Jets Subjected to coanda Effect
- Coanda Effect on Bubble Characteristics in a Bubbling Jet Rising Near the Side Wall of a Cylindrical Vessel
- Flow Establishment Time of a Water Bath Contained in a Cylindrical Vessel Set in Sudden Rotation
- Model Study of Fluid Flow Phenomena in a Bottom Blown Bath in the Presence of Reverse Emulsification
- Effects of the Physical Properties of Top Oil Layer on Bubble and Liquid Flow Characteristics in a Bottom Blown Water Bath
- Numerical Analysis of Transient Flow in a Water Bath Contained in a Cylindrical Vessel Suddenly Set in Rotation
- Prediction of the Occurrence of Swirling Liquid Jet Generated by Off-centered Nozzle
- Development of Swirling Flow Generator in Immersion Nozzle
- Swirling Flow Effect in Immersion Nozzle on Flow in Slab Continuous Casting Mold
- Formation of Fine Bubble through Swirling Motion of Liquid Metal in the Metallurgical Container
- Prevention of Air Suction from the Contact-part between Sliding Gate and Immersion Nozzle
- Removal of Inclusion through Bubble Curtain Created by Swirl Motion in Submerged Entry Nozzle
- Swirling Effect in Immersion Nozzle on Flow and Heat Transport in Billet Continuous Casting Mold
- Self-Induced Rotary Sloshing Caused by an Upward Off-Centered Jet in a Cylindrical Container
- EFFECT OF LOW-DENSITY PARTICLES ON SWIRLING LIQUID JET IN TRANSIENT PERIOD
- Occurrence Condition of a Swirling Bubbling Jet in a Water Bath Covered with an Oil Layer
- PRACTICAL APPLICATIONS OF SWIRLING JETS TO MIXING PROCESSES(Swirling Flow and Separation)
- FUNDAMENTAL CHARACTERISTICS OF SWIRLING JETS IN CYLINDRICAL VESSEL(Swirling Flow and Separation)
- Prediction of the Occurrence of Swirl Motion at Interface between Stratified Two Liquids
- Rupture Phenomena of Molten Alkali Silicate Thin Films
- Occurrence Condition for a Swirl Motion of a Bath Agitated by Bottom Gas Injection
- Fluid Flow in a Combined Top and Bottom Blown Reactor
- Swinging Motion of Bath Surface Induced by Side Gas Injection
- Prediction of the Occurrence of Swirling Liquid Jet
- Proposal of a Novel Agitation Method using Swirl Motion of Molten Metal Jet
- Processing of Refractory Organic Waste Water Using Ozone and Novel Agitation Method
- Mixing time in a cylindrical bath agitated by swirl motion of water jet
- Swirling Flow Effect in Off-center Immersion Nozzle on Bulk Flow in Billet Continuous Casting Mold
- Swirling Flow Effect in Submerged Entry Nozzle on Bulk Flow in High Throughput Slab Continuous Casting Mold
- Bifurcation Angle Effect on the Separation of Gas and Liquid in Horizontal Y-junction of Different Wettability
- Powder-Metallurgical Process for Producing Metallic Microchannel Devices
- Wettability Effects on Liquid Flow Characteristics in a Bubbling Wall Jet along a Vertical Flat Plate
- Swirling Flow Effect in Bottomless Immersion Nozzle on Bulk Flow in High Throghput Slab Continuous Casting Mold
- Swirling flow control in immersion nozzle for CC process
- Model Experiment on the Production of Silicon Droplet
- Physical characteristics of a Horizontally Injected Gas Jet and Turbulent Flow in Metallurgical Vessels
- Fabrication of Porous Transpiration-Cooling Device by Powder-Metallurgical Microchanneling Process
- Effect of Parallel Flow on Frequency of Bubble Formation from Single-Hole Nozzle under Micro-Gravity Conditions
- Formation of Nanoporous Anodic Oxide Films on Ti-Al Microchannel Walls
- Formation Mechanism of Microchannels and Lining Layers in Sintered Iron Powder Compacts with Copper Sacrificial Cores
- Empirical Equations for Bubble Formation Frequency from Downward-Facing Nozzle with and without Rotating Flow Effects
- Separation of Gas from Downward Gas-Liquid Two-Phase Flow Using a Y-Junction of Poor Wettability
- Physical Modeling of a Sampler Filling for Molten Steel
- Molten Metal Flow Measurement Using Cylinder and Hall Element
- An Air Cavity Formed Behind a Poorly Wetted Sphere Penetrating into a Water Bath
- Spout Eye Area in Ladle Refining Process
- Model Experiments on the Mixing Time in a Bottom Blown Bath Covered with Top Slag
- Swirl Motions of Two Bubbling Jets Induced by Bottom Gas Injection
- Unsteady Motions of Cylindrical Bath Caused by Offset Bottom Gas Injection
- Cold Model Study of the Effects of Density Difference and Blockage Factor on Mold Powder Entrainment
- Numerical Simulation on a Horizontal Flow Pattern of Jet-induced Rotary Sloshing in a Cylindrical Container
- The Coordination of F Ions around Al and Ca Ions in Molten Aluminosilicate Systems
- The Role of Ca and Na Ions in the Effect of F Ion on Silicate Polymerization in Molten Silicate System
- The Estimation of the Iso-viscosity Lines in Molten CaF_2-CaO-SiO_2 System
- Swirl Motions in a Cylindrical Bath Induced by Gas Injection under Reduced Pressure on Surface
- Formation of Porous Intermetallic Thick Film by Ni-Al Microscopic Reactive Infiltration
- Effect of Swirl Motion on Mixing Time in Water Bath Agitated by Upward Gas Injection
- Cold Model Experiment on Fluid Flow Phenomena in Hot Dip Plating Bath
- H202 INTERACTION BETWEEN TWO BUBBLING JETS DUE TO COANDA EFFECT(Bubble behavior)
- Karman Vortex Probe for the Detection of Molten Metal Surface Flow in Low Velocity Range
- Swirl Motion of a Mercury Jet Appearing in a Cylindrical Vessel in Transient Period
- Model Study on a Swirl Motion of a Bubbling Jet Generated in a Wastewater Bath Covered with Top Oil Layer
- A bouncing droplet on an inclined hydrophobic surface
- A Method for Measuring Particle Size in Overlapped Particle Images
- Water Model Experiments on the Effect of an Argon Bubble on the Meniscus Near the Immersion Nozzle
- Model Study of the Rupture Phenomena of a Metal Droplet Growing on a Slag-Metal Interface
- Particle Layer Thickness Effect on Particle Entrainment in a Mechanically Agitated Bath
- Promotion of Uniform Dispersion of Fine Particles into a Mechanically Agitated Steel Bath
- Water-model Experiment on Melting Powder Trapping by Vortex in the Continuous Casting Mold
- Repulsive Capillary Force between two Plates Linked by a Concave Molten Slag Bridge
- Instability Phenomena at Bath Surface Induced by Top Lance Gas Injection
- Wettability Effect on a Single Bubble Rising in Stagnant Water Contained in a Vertical Circular Pipe
- Correlation of Flow Establishment Time for Uniform Dispersion of Fine Particles in a Bath with an Immersion Cylinder
- Mixing Time in a Side-Blown Converter
- Downward Air-water Two-phase Flow Near the Outlet of a Model Immersion Nozzle
- Prediction of Argon Gas Attachment to Sliding Gate in Immersion Nozzle
- Model Experiments on Transient Swirl Motion of a Wastewater Jet Generated by J-Shaped Lance
- Mathematical Modeling of Flow and Inclusion Motion in Vessel with Natural Convection
- Preface to the Special Issue on "Mathematical Modeling of Iron and Steel Making Processes"
- The Coanda Effect on Budding Jet behind a Horizontally Placed Circular Cylinder
- Control of Reverse Emulsification and Mixing Time in a Bottom Blown Bath Covered with Top Slag
- Wettability Effect of Vessel Wall on Swirl Motion of Bubbling Jet in Cylindrical Bath
- Model Experiment on the Behavior of Argon Gas in Immersion Nozzle
- Mixing Time in a Bath Agitated Simultaneously by Bottom Gas Injection and Side Liquid Injection
- Unsteady Pressure Coefficient around an Elliptic Immersion Nozzle
- The Coordination of F Ions around Mg and Ca Ions in Molten CaO-CaF_2-MgO-SiO_2 System at 1873K
- Cold Model Experiment on Melting Phenomena of Zn Ingot in Hot Dip Plating Bath
- Cold Model Experiment on Dispersion of Melted Ingots in Hot Dip Plating Bath
- Effects of Snout and Support Roll on Transport Phenomena in a Hot Dip Plating Bath
- Size Effect on Dynamic Behavior of Dross in Model Hot Dip Plating Bath
- Filament and Droplets Formed Behind a Solid Sphere Rising Across a Liquid-Liquid Interface
- Model Experiment on the Dispersion of Fine Particles in a Molten Metal Bath Agitated by Plunging Jet
- Non-contact Sensor for the Measurement of Meniscus Velocity of Molten Metal Flow
- Transient Flow Analysis of Stratified Two Liquid Layers Contained in Rotating Cylindrical Vessel
- Rapid Mixing and Separation of Molten Slag and Metal Using Cylindrical and Baffled Vessels Suddenly Set in Rotation
- Steady and Periodical Bubble Attachment to the Sliding Gate in Immersion Nozzle
- Development of a Laser Optical Sensor for Measuring Bubble Characteristics in an Oily Liquid Bath