Low-Temperature Process of Fine-Pitch Au–Sn Bump Bonding in Ambient Air
スポンサーリンク
概要
- 論文の詳細を見る
A low-temperature bonding process of 30-μm-pitch Au–Sn microbumps was developed in ambient air by the surface activated bonding (SAB) method. The surface activated process, such as Ar plasma pretreatment, is essential for Au–Sn low-temperature bonding. With a total of 4908 connections, the bond yield reaches 100% at a bonding temperature of 100–200 °C in ambient air. No electrical short circuit occurs between two adjacent bumps under the optimized bonding pressure. The bonding strength is larger than 10 MPa. Scanning electron microscope (SEM) and electron probe micro analyzer (EPMA) observations of the cross-sectional bonded interfaces were performed. Intermetallic compounds (IMCs) of AuSn, AuSn2, and AuSn4 appear around the bonded interfaces in the bonding at 100 and 150 °C. More one phase, a thin Au5Sn layer, was detected in the bonding at 200 °C. The bonding feasibility of Au–Sn flip-chip microbumps is confirmed at 100–200 °C in ambient air.
- 2007-04-30
著者
-
HUTTER Matthias
Fraunhofer IZM
-
Wang Ying-hui
Department Of Precision Engineering School Of Engineering The University Of Tokyo
-
Suga Tadatomo
Department Of Precision Engineering Faculty Of Engineering University Of Tokyo
-
Nishida Kenji
Materials Analysis Station National Institute For Materials Science
-
Kimura Takashi
Fraunhofer Institute for Reliability and Microintegration, IZM-Berlin, Gustav-Meyer-Allee 25, D-13355 Berlin, Germany
-
Nishida Kenji
Materials Analysis Station, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
-
Hutter Matthias
Fraunhofer Institute for Reliability and Microintegration, IZM-Berlin, Gustav-Meyer-Allee 25, D-13355 Berlin, Germany
関連論文
- P-MNS-07 NANOTRANSFER METHOD FOR THE FERROELECTRIC FILMS ONTO THE POLYMER SUBSTRATE(Micro/Nanosystem Science and Technology,Technical Program of Poster Session)
- A Low Temperature Process of Bonding Fine Pitch Au/Sn Bumps in Air
- Study on Sn-Ag Oxidation and Feasibility of Room Temperature Bonding of Sn-Ag-Cu Solder
- Low-Temperature Direct Bonding of Flip-Chip Mountable VCSELs with Au-Au Surface Activation
- Effect of Surface Contamination on Solid-State Bondability of Sn-Ag-Cu Bumps in Ambient Air
- Isothermal Fatigue Properties of Sn-Ag-Cu Alloy Evaluated by Micro Size Specimen
- Low-Temperature Process of Fine-Pitch Au–Sn Bump Bonding in Ambient Air
- Evaluation of Alignment Accuracy for Wafer Bonding Using Moire Technique
- Void Free Room Temperature Silicon Direct Bonding by Sequential Plasma Activated Process
- Low Temperature Interconnection of Cu Micro-bump on Polyimide and Ni/Au Film by Surface Activated Flip Chip Method
- Transmission Electron Microscopy of Bi(Pb)-Sr-Ca-Cu-O Superconductor Prepared by the Intermediate Pressing Process
- Low-Temperature Bumpless Bonding for Surface Acoustic Wave Components
- Measurement of Alignment Accuracy for Wafer Bonding by Moiré Method
- Void-Free Room-Temperature Silicon Wafer Direct Bonding Using Sequential Plasma Activation
- Study on Homogeneous Wafer Level Dielectric Film Preparation Using Chemical Solution Deposition Method
- Fabrication and Characterization of Ferroelectric PZT and BaTiO3 Thin Films on Releasable Electrode Structures
- Homogenizing and Applying Dielectric Film to Wafer-Level Film Preparation
- Study on Homogeneous Wafer Level Dielectric Film Preparation Using Chemical Solution Deposition Method