Comparison of Near Wake-Flow Structure behind a Solid Cap with an Attached Bubble and a Solid Counterpart
スポンサーリンク
概要
- 論文の詳細を見る
An experiment to study the near-wake flow structure behind an air bubble attached to a cap and separately, a solid equivalent was conducted. The objective was to elucidate the near-wake characteristics of the "cap-bubble" relative to the solid; in particular, to elucidate the role of the "moving tail". Experiments were performed in 80×80mm^2×1m tall channel with each object suspended in downward flow of water. Both the cap-bubble and solid had an approximate equivalent diameter, D_<eq>〜11.5mm (volume〜0.8mL), The average downward flow velocity (U〜25cm/s〜rise velocity of bubble) defined Reynolds number was, 2450<Re_<Deq><2890. The Eotvos and Weber numbers were, 17.8<Eo<17.85, 6.04<We<6.06. Particle Image Velocimetry using a cross-correlation method was used to generate velocity data; vorticity, turbulent kinetic energy (TKE) and other parameters we then calculated. Graphic and numerical comparisons between the objects led to the following: 1) for the cap-bubble, the influence on the flow structure due to motion of the tail is relatively minor, 2) tail motion contributes to transverse fluctuations and uniformity in TKE distribution and 3) object deformation, oscillation and gyration localizes the flow structure in contrast to a solid object. Results are discussed.
- 一般社団法人日本機械学会の論文
- 2006-08-15
著者
-
Hishida Koichi
Department Of System Design Engineering Keio University
-
Hishida Koichi
Department Of Mechanical Engineering Keio University
-
TOKUHIRO Akira
Mechanical and Nuclear Engineering Department, Kansas State University
-
NO Hidekazu
Department of Nuclear Engineering, University of Missouri-Rolla
-
CALL Michel
Department of Nuclear Engineering, University of Missouri-Rolla
-
Call Michel
Department Of Nuclear Engineering University Of Missouri-rolla
-
No Hidekazu
Department Of Nuclear Engineering University Of Missouri-rolla
-
Tokuhiro Akira
Mechanical And Nuclear Engineering Department Kansas State University
関連論文
- TED-AJ03-370 Planar Measurement of Local Characteristics of Impinging Spray on Heating Plate
- Improvement of Signal Processing for Ultrasonic Velocity Profiler : Comparison of Cross-Correlation and Pulse-Doppler Methods
- TED-AJ03-378 MIXING CONTROL BY ARRAY OF JETS WITH NEURAL NETWORK
- Enhancement Mechanism in Convective Heat Transfer by an Effective Utilization of Droplet Inertia
- F204 CHARACTERISCTICS OF EVAPORATING DROPLETS DISPERSION SUSPENDED IN ISOTROPIC TURBULENCE(DNS and computational procedure for turbulence)
- D310 THERMOELECTRIC PHENOMENA IN MICROSCALE THIN-FILM THERMOCOUPLES(Micro-scale phenomena)
- A Calculation Procedure for Two-Dimensional Parabolic Two-Phase Flows Using Independent Computational Grids for Each Phase : Fluids Engineering
- TED-AJ03-134 INVESTIGATION ON HEAT TRANSFER CHARACTERISTICS OF DRAG-REDUCING FLOW WITH SURFACTANT ADDITIVE BY SIMULTANEOUS MEASUREMENTS OF TEMPERATURE AND VELOCITYFLUCTUATIONS IN THERMAL BOUNDARY LAYER
- D203 VELOCITY AND TEMPERATURE MEASUREMENTS IN HEAT TRANSFER OF SWIRLING IMPINGING JETS(Temperature measurement)
- Neural Network Control of Temperature Profile by Impinging Jet Arrays(Jets, Wakes and Separated Flows)
- Comparison of Near Wake-Flow Structure behind a Solid Cap with an Attached Bubble and a Solid Counterpart
- NEURAL NETWORK CONTROL OF TEMPERATURE PROFILE BY IMPINGING JET ARRAYS(Flow Control 1)
- Electrokinetic effects on motion of submicron particles in microchannel
- Measurement of Vapor Concentration Distribution in Spray by Laser Induced Fluorescence
- Non-Intrusive Velocity Measurement of Millichannel Flow by Spontaneous Raman Imaging
- Effect of Microscale Surface Geometry of Electrodes on Performance of Microbial Fuel Cells
- Velocity Measurement of Sub-Millimeter-Scale Gas Flow by Spark Tracing Method