Optimization of Magnetic Circuit Geometry for Eddy-current Type Proximity Sensor(Session 6 : Sensing Devices)
スポンサーリンク
概要
- 論文の詳細を見る
Eddy-current type proximity sensor is a non-contact type sensing device to detect the approach of a conductor by increase of eddy current loss in the excitation coil. In this paper, actual proximity sensor is firstly calculated by FEM to verify the validity of numerical analysis results and study about electromagnetic properties of proximity sensor. Furthermore, two models that are modified magnetic circuit geometry based on the actual sensor are proposed and calculated by FEM. Results of numerical experiences are shown as enhanced sensing properties. In conclusions, knowledegs about optimal design for magnetic circuit geometry of the proximity sensor are shown.
- 社団法人電子情報通信学会の論文
- 2004-10-15
著者
-
Hayashi Takumi
Advance Automation Company Yamatake Corporation
-
SAWA Koichiro
Department of System Design Engineering, Faculty of Science and Technology, Keio University
-
Sawa Koichiro
Nippon Institute of Technology
-
Sawa Koichiro
Department Of System Design Engineering Faculty Of Science And Technology Keio University
-
Honma Takashi
Advance Automation Company Yamatake Corporation
-
UEDA Kuniyoshi
R&D Headquarters, Yamatake Corporation
-
SASAKI Hiroshi
R&D Headquarters, Yamatake Corporation
-
KOIBUCHI Koichi
Department of System Design Engineering, Faculty of Science and Technology, Keio University
-
Sawa Koichiro
Keio Univ. Yokohama‐shi Jpn
-
Ueda Kuniyoshi
R & D Headquarters Yamatake Corporation
-
Koibuchi Koichi
Faculty Of Science And Technology Keio University
-
Sasaki Hiroshi
R & D Headquarters Yamatake Corporation
-
SASAKI Hiroshi
R&D headquarters, Yamatake Corporation
-
UEDA Kuniyoshi
R&D headquarters, Yamatake Corporation
-
HONMA Takashi
Advance Automation Company, Yamatake Corporation
-
HAYASHI Takumi
Advance Automation Company, Yamatake Corporation
関連論文
- Degradation Phenomenon of Electrical Contacts by Hammering Oscillating Mechanism : Contact Resistance (VIII)
- Degradation Phenomenon of Electrical Contacts by Hammering Oscillating Mechanism : Modeling of the Oscillating Mechanism (VI)
- Research of high reliability of noble metal slip-ring for supply of small electric power
- A study of Degradation Phenomenon of Electrical Contacts by Hammering Oscillating Mechanism : modeling (10)
- Effect of Atmosphere Change on Contact Voltage Drop at Sliding Contact
- A Relation between Commutator Erosion and Commutation Arc for DC Motor
- A Study on Wear of Carbon Flat Commutator and Brush of DC Motor for Automotive Fuel Pump
- Effect of Inert Gas on Surface Film Formation and on Voltage Drop of Sliding Contacts(Recent Development of Electro-Mechanical Devices (IS-EMD 2002))
- An Effect of Inert Gas on Surface Film Formation and Voltage Drop of Sliding Contacts (国際セッションIS-EMD2002〔英文〕)
- Development of the Lead-Free Brush Material for the High-Load Starter(Electromechanical Devices and Components)
- Development of the Lead-Free Carbon Brush Material for Starters(Automotive Application, IS-EMD2004-Recent Development of Electro-Mechanical Devices)
- Consideration on Contact Mechanism of YBaCuO Bulk Superconductor with Deposited Metal Layer(Contact Phenomena,Recent Development of Electromechanical Devices (Selected Papers from ICEC2006))
- Effect of Inert Gas on Surface Film Formation and on Voltage Drop of Sliding Contacts
- A Sudden Increase of Contact Voltage Drop at Gas Introduction into Low Pressure Atmosphere
- An Investigation for the Method of Lifetime Prediction of Ag-Ni Contacts for Electromagnetic Contactor (国際セッションIS-EMD2005) -- (Contactors & Circuit Breakers)
- Fabrication Process of Nonarcing Power MEMS Switch(Relays and Switches, IS-EMD2004-Recent Development of Electro-Mechanical Devices)
- Fabrication process of non arcing power MEMS relay(Session 3 : Relays)
- An Influence of Atmospheric Humidity and Temperature on Brush Wear of Sliding Contact(Special Issue on Current Electromechanical Devices and Their Materials with Recent Innovations)
- Numerical Study on Electromagnetisms and Material Characteristics of Magnetic Flux Shield for Eddy-Current Type Proximity Sensor(Signal Transmission & Sensing,Recent Development of Electromechanical Devices (Selected Papers from ICEC2006)
- Characteristic Analysis and Enhancement of Sensing Property for Eddy-Current Type Proximity Sensor(Sensing Devices, IS-EMD2004-Recent Development of Electro-Mechanical Devices)
- Optimization of Magnetic Circuit Geometry for Eddy-current Type Proximity Sensor(Session 6 : Sensing Devices)
- Application of a Digital Scanning Laser Microscope to 3-D Analysis of Contact Surface Damages(Recent Development of Electro-Mechanical Devices (IS-EMD 2002))
- An experimental Study on operating characteristics of Ag, Pd and Cu contacts in argon atmosphere (国際セッションIS-EMD2002〔英文〕)
- A Study on Material Transfer and Erosion Characteristics of Ag, Pd and Cu Contacts in Nitrogen Atmospher
- Characteristics of a sliding system with Au-plated slip-ring and AgPd brush for power supply(Session 7 : Contact Phenomena)
- A study on influence of surrounding atmosphere to gaseous phase transition in break arc
- Commutation Phenomena of DC Motor in Ethanol Fuel
- A Study on Wear of Brush and Carbon Flat Commutator of DC Motor for Automotive Fuel Pump
- Special Issue on Micromachine Technology
- Characteristics of Flat Commutator on DC Motor for Automotive Fuel Pump (国際セッションIS--EMD 2003) -- (Session 3 Sliding contacts and connectors)
- Recent Researches and New Trends of Electrical Contacts(Special Issue on Current Electromechanical Devices and Their Materials with Recent Innovations)
- Characteristics of Flat Commutator on DC Motor for Automotive Fuel Pump
- Mass Change and Surface Morphology of Contact in Electromagnetic Contactor (国際セッションIS-EMD2002〔英文〕)
- Influence of Voltage on Arc Characteristics and Electrode Mass Change of AgNi Contacts for Electromagnetic Contactors
- Degradation Phenomenon of Electrical Contacts using a Micro-Sliding Mechanism : Minimal Sliding Amplitudes estimated under some conditions by the Mechanism (18)
- An experiment on carbon Commutator and Brush Wear by Arc Discharge
- Degradation Phenomenon of Electrical Contacts using a Micro-Sliding Mechanism : Minimal Sliding Amplitudes estimated under some conditions by the Mechanism (18)
- Degradation phenomenon of electrical contacts using a hammering oscillating mechanism : A fundamental study on the performance of the oscillating mechanism (25)