粒子強化型 P/M Ti-6Al-2Sn-4Zr-2Mo/TiB 複合材料の基質の金属組織制御による高サイクル疲労強度の向上
スポンサーリンク
概要
- 論文の詳細を見る
The present authors have previously shown that in the Ti-6Al-2Sn-4Zr-2Mo/10TiB particulate composites the fatigue fracture originated neither from the interior of particulate nor from the particulate/matrix interface, but rather from the matrix area of the composites. This finding strongly suggested that the high cycle fatigue strength is related with the matrix microstructure. Therefore, the present study aimed at improving the high cycle fatigue strength by the modification of matrix microstructure. The Ti-6Al-2Sn-4Zr-2Mo/10TiB particulate composites were produced by the blended elemental P/M method using extra low chlorine titanium powder smaller than 45μm in diameter. The smooth axial fatigue tests were carried out at an R ratio of 0.1 in the load-controlled mode. The matrix microstructure was highly dependent on the cooling rate after the sintering treatment. The faster cooling rate of 10K/sec produced the well-defined colony microstructure. The massive colony microstructure was obtained by the cooling rate slower than 0.3K/sec. The modification of the matrix microstructure from a colony into a fine acicular α microstructure resulted in the increase in high cycle fatigue strength. For example, fatigue strength at 10^7 cycles was increased from 490MPa to 550MPa. The three main contributions to the fatigue strength were suggested as the contribution from the increase in Young's modulus (18%), tensile strength (39%) and microstructural modification (43%), respectively.
- 社団法人日本鉄鋼協会の論文
- 1998-09-01
著者
-
金 成俊
韓国機械研究院
-
河部 義邦
金属材料技術研究所部長
-
江村 聡
物質・材料研究機構
-
萩原 益夫
金属材料技術研究所筑波支所
-
江村 聡
金属材料技術研究所第3研究グループ (先進耐熱材料)
-
江村 聡
物材機構
-
河部 義邦
金属材料技術研究所
-
萩原 益夫
金材技研
-
萩原 益夫
金属材料技術研究所
関連論文
- 「材料の安全性」を考える
- 組織制御を施した素粉末混合法 Ti-5Al-2.5Fe 合金の製造とその機械的性質
- 特集「チタンのユビキタス化戦略」によせて
- α-β型チタン合金の組織制御を施した素粉末混合法による高性能化
- Fe - 22Cr - 21Ni - 6Mo - 0.3N スーパーオーステナイト系ステンレス鋼におけるσ相の析出挙動及び結晶学
- β型チタン合金のプラズマ電子ビーム溶解
- 700 Ti-15V-3Cr-3Sn-3Al 合金の電子ビーム溶接継手の機械的性質(チタン, 萌芽・境界技術, 日本鉄鋼協会第 113 回(春季)講演大会)
- 844 β型合金 Ti-V-Mo-Cr-Fe-Zr-Al 系の組成の検討(超塑性, 萌芽・境界技術, 日本鉄鋼協会第 112 回(秋季)講演大会)
- 837 チタン合金のプラズマ・電子ビーム溶解(超塑性, 萌芽・境界技術, 日本鉄鋼協会第 112 回(秋季)講演大会)
- 溶体化時効処理 Ti-6Al-4V 合金の電子ビーム溶接継手特性(チタンおよびチタン合金)