Outflow Characteristics of a Pressure Medium during Sheet Hydroforming

スポンサーリンク

概要

• 論文の詳細を見る

• The outflow characteristics of a pressure medium during a sheet hydroforming process have been studied experimentally by directly measuring the hydraulic pressure distribution. Initial measurements of the outflow of the pressure medium though the gap between two clamped dies were carried out in order to verify the method for measuring the hydraulic pressure distribution employed in this study and to investigate the basic properties of the outflow. The upward forces were calculated by integrating the measured hydraulic pressure during the outflow and found to be in satisfactory balance with the clamping forces, which demonstrates the validity of this measurement method. Furthermore, we suggest that the critical outflow pressure can be predicted by considering the force equilibrium. An experimental investigation of a square-cup sheet-hydroforming process was then carried out. The upward forces were calculated by integrating the measured hydraulic pressure and again found to be in satisfactory balance with the forming forces at the beginning of the process, which shows that the critical outflow pressure can also be predicted for square-cup deep-drawing processes. The hydraulic pressure distributions in the flange area and the chamber change significantly as the sheet conforms to the die shoulder, and the friction loss of hydraulic pressure at the die shoulder becomes large. These results indicate that the magnitude of the fluid-lubrication effect on the drawability of the sheet can vary with the stage of sheet deformation.

• 社団法人 日本鉄鋼協会の論文
• 2009-02-15

著者

• HAMA Takayuki

  Department of Energy Science and Technology, Kyoto University

• Hama Takayuki

  Department Of Energy Science And Technology Kyoto University

• Fujimoto Hitoshi

  Department Of Biological Sciences Graduate School Of Bioscience And Biotechnology Tokyo Institute Of

• Takuda Hirohiko

  Department Of Energy Science And Technology Graduate School Of Energy Science Kyoto University

• Matsushima Keita

  Department Of Energy Science And Technology Kyoto University

• KURISU Ken

  Department of Energy Science and Technology, Kyoto University

• Kurisu Ken

  Department Of Energy Science And Technology Kyoto University

関連論文

• Springback Characteristics of Magnesium Alloy Sheet AZ31B in Draw-Bending
• Effect of Tool-Modeling Accuracy on Square-Cup Deep-Drawing Simulation
• Effect of Force Correction Algorithm Arising from Change of Tool Normal on Sheet Metal Forming Simulation(Recent Advances in Materials and Processing (I))
• 533 A stable and fast new contact search algorithm for FEM simulation of metal forming process
• Simulation of Hammering Hydroforming by Static Explicit FEM
• Analysis of Hydrostatic Tube Bulging with Cylindrical Die Using Static Explicit FEM
• ARC3, a Chloroplast Division Factor, is a Chimera of Prokaryotic FtsZ and Part of Eukaryotic Phosphatidylinositol-4-phosphate 5-kinase
• Nanosecond Time-Resolved Photoinduced Absorption of trans-Polyacetylene
• Forming Limit Prediction in Bore Expansion by Combination of Finite Element Simulation and Ductile Fracture Criterion
• Tensile Properties and Press Formability of a Mg-9Li-1Y Alloy Sheet
• Numerical Simulation of Two Droplets Impinging Successively on a Hot Solid in the Film Boiling Regime
• Predictable Modelling of Heat Transfer Coefficient between Spraying Water and a Hot Surface above the Leidenfrost Temperature
• Numerical Simulation of Successive Collision of Two Liquid Droplets with a Solid Wall
• Correlation between Sheet Deformation and Hydraulic Pressure Variation during Sheet Hydroforming
• Outflow Characteristics of a Pressure Medium during Sheet Hydroforming
• Numerical Study of a Planar Liquid Jet Impinging on a Solid Substrate
• Numerical Study of the Collision Dynamics and Heat Transfer of Water Droplets Impinging on a Hot Solid
• Flow Characteristics of Circular Liquid Jet Impinging on a Moving Surface Covered with a Water Film
• Effect of Outflow Volume of Pressure Medium on Fluid-Lubrication Effect during Sheet Hydroforming
• Formulation of Contact Problems in Sheet Metal Forming Simulation Using Local Interpolation for Tool Surfaces
• A theoretical study on nozzle design for gas-particle mixture flow.
• Optical properties of undoped and AsF5 doped "poly(4,4'-biphenylylene)"films.
• A numerical study on cooling process of hot steel plates by a water curtain.
• Infrared and visible absorption spectra of doped (CH)x,(CD)x, and copolymers ((C2H2)1-y(C2D2)y)x.

もっと見る 閉じる

スポンサーリンク