Development of Fluoride-free Mold Powders for Peritectic Steel Slab Casting
スポンサーリンク
概要
- 論文の詳細を見る
In this paper, titanium-bearing blast furnace slags (CaO–SiO2–TiO2) produced at Panzhihua Iron and Steel Company (P. R. China) is used as the base material to develop fluoride-free (F-free) mold powders to improve the heat transfer between the mold and the strand. Effects of the binary basicity (CaO/SiO2), TiO2, Na2O, Li2O, MgO, MnO and B2O3 on the melting temperature, viscosity and heat flux of F-free mold powders are investigated. The laboratory results indicate that 1) the melting temperature and the viscosity of the F-free powder decrease, as expected, with increasing the content of Li2O, B2O3 and Na2O respectively, but the lowest viscosity is achieved with 6.0 mass% TiO2; 2) the heat flux of the F-free slag film with 1.0–6.0 mass% TiO2 is close to that of a conventional mold slag film with 2.0–10.0 mass% F; 3) the effect of basicity of the F-free powder on the heat flux is the same as the powder bearing fluoride; 4) the heat flux changes significantly with more than 8.0 mass% Na2O and about 4.0 mass% MnO, whereas the effects of Li2O and B2O3 in the F-free powder on heat flux are not significant. The suitable range of main components of the F-free powder with TiO2 is proposed for casting peritectic-grade-steel slabs. The industrial trials of peritectic steel casting, using the proposed F-free flux, reveals a good surface quality of the slab, and well-controlled heat transfer at the continuous casting mold by the F-free powder with the precipitated crystalline phase being perovskite (CaTiO3) instead of cuspidine in the conventional mold slags that contain fluoride.
- 2007-08-15
著者
-
Sridhar Seetharaman
Dep. Of Material Sci. & Engineering Carnegie Mellon Univ.
-
Sridhar Seetharaman
Department Of Materials Science And Engineering Carnegie Mellon University
-
Wen Guanghua
Department of Materials Science and Engineering, Carnegie Mellon University
-
Tang Ping
Department of Materials Science and Engineering, Chongqing University
-
QI Xin
Department of Computer Science and Technology, Tsinghua University
-
Qi Xin
Department Of Computer Science And Technology Tsinghua University
-
Wen Guanghua
Dep. Of Metallurgy Coll. Of Materials Sci. And Engineering Chongqing Univ.
-
Qi Xin
Department Of Metallurgy College Of Materials Science And Engineering Chongqing University
-
LIU Yongqing
Department of Metallurgy, College of Materials Science and Engineering, Chongqing University
-
Liu Yongqing
Department Of Metallurgy College Of Materials Science And Engineering Chongqing University
-
Tang Ping
Dep. Of Metallurgy Coll. Of Materials Sci. And Engineering Chongqing Univ.
関連論文
- 1973KにおけるFe-Al-TiO融液中の脱酸挙動
- 1973KにおけるFe-Al-TiO融液中の脱酸挙動
- An Investigation of the Evaporation of B2O3 and Na2O in F-Free Mold Slags
- The Influence of Al2O3/SiO2 Ratio on the Viscosity of Mold Fluxes
- The Ability of Slags to Absorb Solid Oxide Inclusions
- VLSI Module Placement with Pre-Placed Modules and with Consideration of Congestion Using Solution Space Smoothing(Place and Routing)(VLSI Design and CAD Algorithms)
- VLSI Module Placement with Pre-Placed Modules and with Consideration of Congestion Using Solution Space Smoothing
- The Austenite/Ferrite Front Migration Rate during Heating of IF Steel
- The Transient Stages of Inclusion Evolution During Al and/or Ti Additions to Molten Iron
- Micro-structure Refinement in Low Carbon High Manganese Steels through Ti-deoxidation : Austenite Grain Growth and Decomposition
- Micro-structure Refinement in Low Carbon High Manganese Steels through Ti-deoxidation-Inclusion Precipitation and Solidification Structure
- Development of Fluoride-free Mold Powders for Peritectic Steel Slab Casting
- The Effect of Alloy Solidification Path on Sulfide Formation in Fe-Cr-Ni Alloys
- The Influence of Al_2O_3/SiO_2 Ratio in the Viscosity of Mold Fluxes
- Crystallization Behaviors of Mold Fluxes Containing Li_2O Using Single Hot Thermocouple Technique
- Interface Migration Behavior of the δ→γ Interface in Low Carbon High Manganese Steel Samples De-oxidized with Ti or Al
- Effect of Ti De-oxidation on Solidification and Post-solidification Microstructure in Low Carbon High Manganese Steel
- An Investigation of the Evaporation of B_2O_3 and Na_2O in F-Free Mold Slags
- A subset of breast cancer predisposes to brain metastasis
- Influence of Raw Material Type on Heat Transfer and Structure of Mould Slag
- Micro-structure Refinement in Low Carbon High Manganese Steels through Ti-Deoxidation, Characterization and Effect of Secondary Deoxidation Particles
- Retigeric Acid B Enhances the Efficacy of Azoles Combating the Virulence and Biofilm Formation of Candida albicans
- Effect of Al2O3/SiO2 Ratio on the Viscosity and Structure of Slags
- Molecular Dynamics Study of the Structural Properties of Calcium Aluminosilicate Slags with Varying Al2O3/SiO2 Ratios
- Molecular Dynamics Study of the Structural Properties of Calcium Aluminosilicate Slags with Varying Al_2O_3/SiO_2 Ratios
- Effect of Al_2O_3/SiO_2 Ratio on the Viscosity and Structure of Slags
- Simulation and Characterization on Heat Transfer through Mould Slag Film