Analytical Model of Melting Phenomena for Breaking Relay Contacts
スポンサーリンク
概要
- 論文の詳細を見る
Using the transient current switch circuit in parallel with the energizing contacts, the slow decay of the contact current due to thermal fusion of metal was observed just after the contact voltage exceeded the melting contact voltage Um. At that time, the contact voltage was higher than the boiling contact voltage Ub. These results contradict Holms φθ theory. A new melting model of breaking mechanical contact is proposed. The area surrounding a cluster of contacting a-spots melts, the melt metal diffuses, and the contact spot thermally shrinks. Including the metal phase transition from solid to liquid, the increase of contact resistance is introduced to the electric circuit analysis. The numerical analysis agrees qualitatively with measured V-I characteristics.
- (社)電子情報通信学会の論文
- 2009-08-01
著者
-
Kudo Takayuki
Ishinomaki Senshu University Faculty Of Science And Engineering
-
Takatsu Nobuo
Ishinomaki Senshu University Faculty Of Science And Engineering
-
Takatsu Nobuo
Faculty Of Engineering Tohoku University
-
WAKATSUKI Noboru
Faculty of Science and Engineering, Ishinomaki Senshu University
-
MAEDA Toshiteru
Faculty of Science and Engineering, Ishinomaki Senshu University
-
KUDO Takayuki
Faculty of Science and Engineering, Ishinomaki Senshu University
-
Wakatsuki Noboru
Ishinomaki Senshu University Faculty Of Science And Engineering
-
Wakatsuki Noboru
Faculty Of Science And Engineering At Ishinomaki Senshu University
-
Maeda Toshiteru
Faculty Of Science And Engineering Ishinomaki Senshu University
-
Kudo Takayuki
Faculty Of Science And Engineering Ishinomaki Senshu University
関連論文
- The Bending Strength of Carburized Fine Module Gear Teeth : Carburizing Conditions and Their Effects on the Fatigue Strength
- Bending Strength of Carburized SCM420H Spur Gear Teeth
- Fabrication Process of Nonarcing Power MEMS Switch(Relays and Switches, IS-EMD2004-Recent Development of Electro-Mechanical Devices)
- Fabrication process of non arcing power MEMS relay(Session 3 : Relays)
- High-Speed Forming of Metal Sheets by Electromagnetic Force
- Basic Research on the Vibratory Travelling Element : Travelling mode and Velocity
- Measurement of Bouncing of Reed Switch Due to Coulomb's Electrostatic Force(Relays & Switches,Recent Development of Electromechanical Devices (Selected Papers from ICEC2006))
- Contacting force of a reed switch at breaking operation (国際セッションIS-EMD2005) -- (Relays and Switches)
- Influence of shear vibration over Au-Au electric contact phenomenon (国際セッションIS-EMD2002〔英文〕)
- Time-Coordinated Switching Relay for Arc Discharge Suppression(Relays and Switches, IS-EMD2004-Recent Development of Electro-Mechanical Devices)
- Influence of Shear Vibration over Au-Au Electric Contact Phenomenon(Recent Development of Electro-Mechanical Devices (IS-EMD 2002))
- Influence of Shear Vibration over Au-Au Electric Contact Phenomenon
- Equivalent Circuit Analysis for Time-Coordinated Non-arcing Operation of Reed Switches(Relays & Switches,Recent Development of Electromechanical Devices (Selected Papers from IS-EMD2005))
- Examination of cluster model of arc ignition at electric contacts
- Analysis of electric contacts using an electric conductive cluster and an electric field effect cluster
- Examination of a Langevin-Type Transducer Using a LiNbO_3 Single Crystal
- Measurement of Breaking Phenomena of Ag and Au Crossbar Electric Contacts Depending on Contacting Spots
- Measurement of breaking phenomena of Ag and Au crossbar electric contacts depending on contacting spots (Electromechanical devices)
- Examination of Cluster Model for Metal Melting of Electric Contacts
- Analytical Model of Melting Phenomena for Breaking Relay Contacts
- Analytical Model of Melting Phenomena with Breaking Relay Contacts
- Statistical Analysis of Dynamic Loads on Spur Gear Teeth : Experimental Study
- Statistical Analysis of Dynamic Loads on Spur Gear Teeth : Effect of Shaft Stiffness
- Dynamic Loads on Spur Gear Teeth Caused by Teeth Impact
- Approximate Solution of a Gear System Subjected to Random Excitation
- Jump Phenomena in Gear System to Random Excitation
- Dynamical Distinctive Phenomena in Gear System
- Mechanical Fracture of Piezoelectric Single Crystal Chip Resonator due to High Input Power(Special Issue on Current Electromechanical Devices and Their Materials with Recent Innovations)
- Breaking Contact Phenomena of Time-coordinated Non-arcing Relay(Session 3 -Arc Interruption-)
- Electric Measurement of Melting Phenomena for Breaking Relay Contacts
- Electric Measurement of Melting Phenomena for Breaking Relay Contacts
- Breaking Contact Phenomena of a Time-coordinated Non-arcing Relay
- FOREWORD
- Improving the Sensitivity of H-Type LiTaO_3 Piezoelectric Crystal Gyroscopes (Special Issue on Electromechanical Devices and Their Materials)
- Estimation of Frequency Conversion Efficiency of Lasers with Intracavity Optical Mixing
- LiTaO3 Shear Wave Resonator for Viscosity Measurement of Polymer Liquid in MHz Range
- Experimental Analysis of Transient Phenomena from Metal Melting to Electric Discharge during Breaking Operations of Electric Contacts
- A Study on Shear Wave LiTaO3 Resonators for Viscosity Sensor
- Equivalent Circuit Analysis for the Transient Phenomena from Elastic Contact to Breaking Contact through Metal Melting
- Brillouin Light Scattering from Thin Albumen of Chicken Egg