A Noble Gas Wiping System to Prevent the Edge Overcoating in Continuous Hot-dip Galvanizing
スポンサーリンク
概要
- 論文の詳細を見る
A noble method is proposed to prevent the edge overcoating (EOC) that may develop near the edge of the steel strip in the gas wiping process of continuous hot-dip galvanizing. In our past study (ISIJ International, Vol. 27 (2003), No. 10, pp. 1495–1501), it was found that the EOC is caused by the alternating vortices which are generated by the collision of two opposing jets in the region outside the steel strip. In the present study, the flow field around the gas wiping system has been analyzed numerically and it was found that when the two opposing jets collide at an angle much less than 180°, the alternating vortices disappear and the impinging pressure on the steel strip surface becomes nearly uniform. In order to deflect both jets downward by a certain angle, a cylinder with small diameter is installed tangentially to each exit of the lower lips of the two-dimensional opposing jets. The three dimensional flow field with the proposed device is analyzed numerically by using the commercial CFD software, STAR-CD. And the coating thickness is calculated by solving the boundary layer momentum equation with an integral analysis method. In order to compare the present noble method with the conventional edge baffle plate method to prevent the EOC, the flow field with edge baffle plates is also calculated. The calculation results show that the tangentially installed cylinder at the lower lip of the jet exit is significantly more effective than the edge baffle plate.
- 社団法人 日本鉄鋼協会の論文
- 2006-04-15
著者
-
Chung Myung
Dep. Of Mechanical Engineering Korea Advanced Inst. Of Sci. And Technol. (kaist)
-
Chung Myung
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology (KAIST)
-
Ahn Ki
Department of Obstetrics and Gynecology, Korea University College of Medicine
-
Ahn Ki
Department Of Mechanical Engineering Korea Advanced Institute Of Science And Technology (kaist)
-
Ahn Ki
Department Of Mechanical Engineering Kaist
-
Chung Myung
Department Of Environmental Science Sun Moon University
関連論文
- IS-85 The relationship between serum follicle-stimulating hormone and estradiol levels and urodynamic results in patients with pelvic floor dysfunction(Group11 Women's Health2,International Session)
- Development of Novel Air-knife System to Prevent Check-mark Stain on Galvanized Strip Surface
- CFD Analysis of Sag Line Formation on the Zinc-coated Steel Strip after the Gas-jet Wiping in the Continuous Hot-dip Galvanizing Process
- Development of an in vitro Environmental Monitoring System by Using Immune Cells
- Two-Dimensional Slow Viscous Flow Past a Plate Midway between an Infinite Channel
- Numerical Analysis of Edge Over-coating in Continuous Hot-dip Galvanizing
- 固気二相流に対する二流体乱流モデル
- 二次のクロージャモデルによる熱拡散乱流の数値シミュレーション
- Organ Distribution of Heavy Metals in Autopsy Material from Normal Korean
- A Noble Gas Wiping System to Prevent the Edge Overcoating in Continuous Hot-dip Galvanizing
- Development of Novel Air-knife System to Prevent Check-mark Stain on Galvanized Strip Surface
- IS-101 WRN gene expression in vaginal walls of women with pelvic organ prolapse(Group11 Women's Health1,International Session)
- CFD Analysis of Sag Line Formation on the Zinc-coated Steel Strip after the Gas-jet Wiping in the Continuous Hot-dip Galvanizing Process
- An analytical model of velocity-derivative skewness of rotating homogeneous turbulence
- Numerical Verification of the Performance of Double Jet Air-knife System in Avoiding the Check-mark Stain on the Zinc Coated Surface
- Cryogenic Heat-Exchanger Design for Freeze-out Removal of Carbon Dioxide from Landfill Gas
- Effect of adiponectin and sex steroid hormones on bone mineral density and bone formation markers in postmenopausal women with subclinical hyperthyroidism
- A Two-Fluid Turbulence Model for Gas-Solid Two-Phase Flows.