Constant ΔΚ Fatigue Crack Growth Tests under Programmed Humidity Cycle Conditions-As a Tool to Evaluate the Effect of Humidity on Fatigue Crack Growth of Al-Li Alloys-
スポンサーリンク
概要
- 論文の詳細を見る
The effect of the relative humidity of the laboratory air on the fatigue crack growth rate in 8090 Al-Li alloys has been examined. The constant ΔK fatigue crack growth tests under programmed humidity cycle conditions were carried out to quantify the extent of the increase in fatigue crack growth rates due to the relative humidity. The obtained results are compared to the da/dN-ΔK relationships obtained from the constant amplitude dynamic load fatigue crack growth tests. It was found that the intrinsic fatigue crack growth rate increase with the relative humidity, but the extent of the increase was found to be considerably small compared to the growth rate difference between the laboratory air and vacuum conditions. The constant ΔK test at a high stress ratio under programmed humidity cycle conditions was effective for detecting the relatively small humidity effect on the fatigue crack growth rate.
- 社団法人 日本鉄鋼協会の論文
- 1997-12-15
著者
-
Yoshikawa Akihiko
Undergraduate Student Tokyo Institute Of Technology
-
Kumai Shinji
Department Of Materials Science And Engineering Tokyo Institute Of Technology
-
Higo Yakichi
Precision And Intelligence Laboratory Tokyo Institute Of Technology
-
Higo Yakichi
Precision & Intelligence Laboratory Tokyo Inst. Of Tech.
-
SEKIKAWA Akinori
Tokyo Institute of Technology
-
Kumai Shinji
Department Of Materials Science And Engineering Interdisciplinary Graduate School Of Science And Eng
-
KUMAI Shinji
Department of Material Science and Engineering, Tokyo Institute of Technology
関連論文
- Formation of Internal Crack in High-Speed Twin-Roll Cast 6022 Aluminum Alloy Strip
- Microstructural Refinement of Hyper-Eutectic Al-Si-Fe-Mn Cast Alloys to Produce a Recyclable Wrought Material
- High-Speed Twin-Roll Strip Casting of Al-Mg-Si Alloys with High Iron Content
- Refined Solidification Structure and Improved Formability of A356 Aluminum Alloy Plate Produced using a High-Speed Twin-Roll Strip Caster
- Interfacial Microstructure of Aluminum/Metallic Glass Lap Joints Fabricated by Magnetic Pulse Welding
- Tear Toughness Evaluation of a Permanent Mold Cast A356 Aluminum Alloy Using a Small-size Specimen
- Tear Toughness of Permanent Mold Cast and DC Cast A356 Aluminum Alloys
- Fatigue Tests of Ni-P Amorphous Alloy Microcantilever Beams
- Growth Manner of Intermetallic Compounds at the Weld Interface of Steel/Aluminum Alloy Lap Joint Fabricated by a Defocused Laser Beam
- Molecular Dynamics Simulation of Crystallization in an Amorphous Metal during Shear Deformation
- High-Speed Twin Roll Casting of Thin Aluminum Alloy Strips Containing Fe Impurities
- Origin of Improved Ductility in Semi-Liquid Die-Cast Al-7%Si-0.4%Mg Alloys
- Effects of Dendrite Cell Size and Eutectic Si Particle Morphology on Fatigue Crack Growth in Cast and HIPed AC4CH Alloys
- The Effects of Straining Frequency and Stress Ratio on Polarization Current Responded to Cyclic Strain in a Commercial Iron
- Effects of Extrusion Temperature on Creep Properties of Spray-Formed and Hot-Extruded Al-8.3 mass%Fe Alloys
- Constant ΔΚ Fatigue Crack Growth Tests under Programmed Humidity Cycle Conditions-As a Tool to Evaluate the Effect of Humidity on Fatigue Crack Growth of Al-Li Alloys-
- OS6(4)-16(OS06W0425) The Fracture Toughness and Fatigue Properties of Micro Sized High Strength γ-TiAl
- Simulation and Experimental Analysis of Metal Jet Emission and Weld Interface Morphology in Impact Welding
- OS6(3)-13(OS06W0415) Subtle Non-Newtonian Property Measurement of Micro Fluids Using Squeeze Flow Rheometry
- Influence of Environmental Conditions on the Fatigue Strength of Plastics
- Interfacial Morphology of Magnetic Pulse Welded Aluminum/Aluminum and Copper/Copper Lap Joints
- Growth Manner of Intermetallic Compound Layer Produced at Welding Interface to Friction Stir Spot Welded Aluminum/Steel Lap Joint
- Microstructural Development during Fatigue of a Polycrystalline 3003 Aluminum Alloy
- Characterization of Intermetallic Compound Layer Formed at the Weld Interface of the Defocused Laser Welded Low Carbon Steel/6111 Aluminum Alloy Lap Joint
- Effect of Cooling Rates during Solidification of Al-5.5%Mg-2.3%Si-0.6%Mn and Al-13% Mg_2Si Pseudo-Binary Alloys on Their Secondary-Particle Morphology and Tear Toughness
- Competitive Nucleation and Growth of {111} Ω with {001} GP Zones and θ' in a Stress-Aged Al-Cu-Mg-Ag Alloy
- Effect of Si Content on Strip Thickness and Solidified Structure in High-Speed Twin-Roll Cast Al-Si Alloy Strips
- Effects of Mechanical constraint on the Strength of Ni_3Ge Single Crystals
- Microstructure and Joint Strength of Friction Stir Spot Welded 6022 Aluminum Alloy Sheets and Plated Steel Sheets
- Advanced High-Speed Solid-State Joining of 2024 Aluminum Alloy Studs to 5052 Aluminum Alloy Plates
- Effects of High-Temperature Solutionizing on Microstructure and Tear Toughness of A356 Cast Aluminum Alloy
- High-Speed Deformation and Collision Behavior of Pure Aluminum Plates in Magnetic Pulse Welding
- Microstructural Characterization of Intermediate Layer Produced at Aluminum/Metallic Glass Interface Fabricated by Magnetic Pulse Welding
- Microstructural Characterization of Intermediate Layer Produced at Aluminum/Metallic Glass Interface Fabricated by Magnetic Pulse Welding
- Elastic Properties of Pd-Based Bulk Metallic Glasses Studied by Ultrasouond Spectroscopy
- Influence of probe bottom shape on microstructure and mechanical properties in friction stir spot welded 6022 aluminum alloy sheets
- Casting of Aluminum Alloy Clad Strip using a Roll Caster