The Simulation Test to Start up the PIUS-Type Reactor from Isothermal Fluid Condition
スポンサーリンク
概要
- 論文の詳細を見る
A feedback control system of a primary pump is proposed for a PIUS-type reactor based on the temperature distribution in the lower density lock. This control system maintains the fluid temperature at the axial center of the lower density lock at the average of the fluid temperatures below and above the lower density lock in order to prevent the poison water from penetrating into the core during normal operation. This control system was examined in a series of startup tests under different conditions and the test results demonstrated the effectiveness of the control system to startup the reactor from a small initial temperature difference between primary system and poison water system. The startup of a PIUS-type reactor from an isothermal condition, preventing the inflow of the poison water into the core, is the most difficult transient among normal operations. We installed a preheater system at the exit of the primary pump for the startup test from isothermal condition with the purpose of making a initial temperature difference between primary system and poison water pool. It was confirmed from the results of the tests that the preheater and the present pump feedback control system is quite effective to start up the reactor from an isothermal fluid condition.
- 社団法人 日本原子力学会の論文
- 1995-09-25
著者
-
HAGA Katsuhiro
Japan Atomic Energy Agency
-
Tasaka K
Department Of Nuclear Engineering Nagoya University
-
Kukita Yutaka
Japan Atomic Energy Research Institute
-
HAGA Kazuko
Taiheiyo Consultant Co., Ltd.
-
Haga K
Taiheiyo Consultant Co. Ltd.
-
Tasaka Kanji
Department Of Nuclear Engineering Nagoya University
関連論文
- Mockup Experiments on Investigate the Leak Rate Correlation between Mercury and Helium for the Mercury Target System of J-PARC
- Mitigation Technologies for Damage Induced by Pressure Waves in High-Power Mercury Spallation Neutron Sources (II) : Bubbling Effect to Reduce Pressure Wave
- Microbubble Formation at a Nozzle in Liquid Mercury
- Distribution of Microbubble Sizes and Behavior of Large Bubbles in Mercury Flow in a Mockup Target Model of J-PARC
- ROSA/AP600 Testing : Facility Modifications and Initial Test Results
- Silicate Anion Structural Change in Calcium Silicate Hydrate Gel on Dissolution of Hydrated Cement
- Dissolution Phenomena of CaO-SiO_2-H_2O Gel at Ca/Si>1 Coexisting with Ettringite System
- Distribution of Microbubble Sizes and Behavior of Large Bubbles in Mercury Flow in a Mockup Target Model of J-PARC
- Differences and similarity in the dynamic and acoustic properties of gas microbubbles in liquid mercury and water
- Intentional Depressurization of Steam Generator Secondary Side during a PWR Small-Break Loss-Coolant Accident
- Interfacial Friction Factor for High-Pressure Steam/Water Stratified-Wavy Flow in Horizontal Pipe
- Sub- to Supercritical Flow Transition in a Horizontally-Stratified Two-Phase Flow in PWR Hot Legs
- Experiments on Mercury Circulation System for Spallation Neutron Target
- ICONE11-36146 WATER FLOW EXPERIMENTS AND ANALYSES ON THE CROSS-FLOW TYPE MERCURY TARGET WITH PERFORATED PLATES
- ICONE11-36101 MERCURY TARGET THERMAL HYDRAULIC DEDIGN FOR JAERI SPALLATION NEUTRON SOURCE
- ICONE11-36079 Mercury Erosion Experiments for Spallation Target System
- The Simulation Test to Start up the PIUS-Type Reactor from Isothermal Fluid Condition
- Analysis of System Thermal Hydraulic Responses for Passive Safety Injection Experiment at ROSA-IV/Large Scale Test Facility. Using JAERI Modified Version of RELAP5/MOD2 Code.:Using JAERI Modified Version of RELAP5/MOD2 Code
- Onset criterion for liquid entrainment in reflooding phase of LOCA.
- Simulation of PWR Turbine Trip Transient in ROSA-IV Large Scale Test Facility
- Investigation of effect of pressure control system on BWR LOCA phenomena using ROSA-III test facility.